stm32l151初始化时间STM32L431时钟系统初始化示例

导读STM32L431有4个时钟源可以作为系统时钟：HSE:高速外部晶体或陶瓷谐振器,4MHz-48MHzHSI16:高速内部RC振荡器,16MHzMSI:多种....

STM32L431有4个时钟源可以作为系统时钟：

• HSE: 高速外部晶体或陶瓷谐振器, 4 MHz - 48 MHz

• HSI16: 高速内部RC振荡器, 16 MHz

• MSI: 多种频率可选的内部RC振荡器, 100KHz - 48MHz 之间共有12档频率可选

• PLL: 系统内部的PLL, 可以将HSE, HSI16, MSI作为输入时钟源, 设置倍频系数, 输出最高80MHz作为系统时钟

系统上电后, 默认MSI(4MHz)作为系统时钟, 但本文将使用HSE(24.576MHz的外部晶振)作为PLL的输入时钟源，使PLL产生73.728MHz作为系统时钟.

下图为STM32L431的时钟系统结构框图：

实现HSE作为PLL时钟源，并将PLL输出作为系统时钟的源程序如下：

typedef struct{ __IO uint32_t CR; /*!< RCC clock control register, */ __IO uint32_t ICSCR; /*!< RCC Internal Clock Sources Calibration Register, */ __IO uint32_t CFGR; /*!< RCC clock configuration register, */ __IO uint32_t PLLCFGR; /*!< RCC System PLL configuration register, */ __IO uint32_t PLLSAI1CFGR; /*!< RCC PLL SAI1 Configuration Register, */ uint32_t RESERVED_0; /*!< Reserved, */ __IO uint32_t CIER; /*!< RCC Clock Interrupt Enable Register, */ __IO uint32_t CIFR; /*!< RCC Clock Interrupt Flag Register, */ __IO uint32_t CICR; /*!< RCC Clock Interrupt Clear Register, */ uint32_t RESERVED0; /*!< Reserved, */ __IO uint32_t AHB1RSTR; /*!< RCC AHB1 peripheral reset register, */ __IO uint32_t AHB2RSTR; /*!< RCC AHB2 peripheral reset register, */ __IO uint32_t AHB3RSTR; /*!< RCC AHB3 peripheral reset register, */ uint32_t RESERVED1; /*!< Reserved, */ __IO uint32_t APB1RSTR1; /*!< RCC APB1 macrocells resets Low Word, */ __IO uint32_t APB1RSTR2; /*!< RCC APB1 macrocells resets High Word, */ __IO uint32_t APB2RSTR; /*!< RCC APB2 macrocells resets, */ uint32_t RESERVED2; /*!< Reserved, */ __IO uint32_t AHB1ENR; /*!< RCC AHB1 peripheral clock enable register, */ __IO uint32_t AHB2ENR; /*!< RCC AHB2 peripheral clock enable register, */ __IO uint32_t AHB3ENR; /*!< RCC AHB3 peripheral clock enable register, */ uint32_t RESERVED3; /*!< Reserved, */ __IO uint32_t APB1ENR1; /*!< RCC APB1 macrocells clock enables Low Word, */ __IO uint32_t APB1ENR2; /*!< RCC APB1 macrocells clock enables High Word, */ __IO uint32_t APB2ENR; /*!< RCC APB2 macrocells clock enabled, */ uint32_t RESERVED4; /*!< Reserved, */ __IO uint32_t AHB1SMENR; /*!< RCC AHB1 macrocells clocks enables in sleep mode, */ __IO uint32_t AHB2SMENR; /*!< RCC AHB2 macrocells clock enables in sleep mode, */ __IO uint32_t AHB3SMENR; /*!< RCC AHB3 macrocells clock enables in sleep mode, */ uint32_t RESERVED5; /*!< Reserved, */ __IO uint32_t APB1SMENR1; /*!< RCC APB1 macrocells clock enables in sleep mode Low Word, */ __IO uint32_t APB1SMENR2; /*!< RCC APB1 macrocells clock enables in sleep mode High Word, */ __IO uint32_t APB2SMENR; /*!< RCC APB2 macrocells clock enabled in sleep mode, */ uint32_t RESERVED6; /*!< Reserved, */ __IO uint32_t CCIPR; /*!< RCC IPs Clocks Configuration Register, */ __IO uint32_t RESERVED7; /*!< Reserved, */ __IO uint32_t BDCR; /*!< RCC Vswitch Backup Domain Control Register, */ __IO uint32_t CSR; /*!< RCC clock control & status register, */ __IO uint32_t CRRCR; /*!< RCC Clock recovery RC register, */ __IO uint32_t CCIPR2; /*!< RCC Peripherals independent clock configuration register, */} RCC_TypeDef;#define PERIPH_BASE ((uint32_t)0x40000000)#define AHB1PERIPH_BASE (PERIPH_BASE 0x00020000)#define RCC_BASE (AHB1PERIPH_BASE 0x1000)#define RCC ((RCC_TypeDef *) RCC_BASE)#define RCC_CR_HSEON ((uint32_t)0x00010000)#define RCC_CR_HSERDY ((uint32_t)0x00020000)#define RCC_CR_PLLON ((uint32_t)0x01000000)#define RCC_CR_PLLRDY ((uint32_t)0x02000000)#define RCC_PLLCFGR_PLLSRC_HSE ((uint32_t)0x00000003)#define RCC_PLLCFGR_PLLREN ((uint32_t)0x01000000)#define RCC_CFGR_HPRE_DIV1 ((uint32_t)0x00000000)#define RCC_CFGR_PPRE1_DIV4 ((uint32_t)0x00000500)#define RCC_CFGR_PPRE2_DIV4 ((uint32_t)0x00002800)#define RCC_CFGR_SW_PLL ((uint32_t)0x00000003)#define RCC_CFGR_SWS ((uint32_t)0x0000000C)#define RCC_CFGR_SWS_PLL ((uint32_t)0x0000000C)/** 初始化STM32L431时钟系统** 输入时钟: HSE(24.576MHz)** PLL输出: 73.728MHz*/void RCC_Init(void){ /***************************************** * 1. 启动HSE ******************************************/ // MSI = 4MHz, MSI时钟开 RCC->CR = 0x00000063; // HSE时钟开 RCC->CR |= RCC_CR_HSEON; // 等待HSE工作正常 for(;;) { if (RCC->CR & RCC_CR_HSERDY) break; } /***************************************** * 2. 启动PLL ******************************************/ // 此寄存器设置了: PLLN = 12 , PLLM = 2 , PLLR = 2 RCC->PLLCFGR = 0x00000C10; // 将HSE(24.576M)指定为PLL的时钟源, PLLSRC = 24.576MHz RCC->PLLCFGR |= RCC_PLLCFGR_PLLSRC_HSE; // fVCO = PLLSRC * (PLLN / PLLM) = 24.576M * (12 / 2) = 147.456M // PLLCLK = fVCO / PLLR = fVCO / 2 = 73.728M // PLL开 RCC->CR |= RCC_CR_PLLON; // 等待PLL工作正常 for(;;) { if (RCC->CR & RCC_CR_PLLRDY) break; } // PLLCLK输出允许 RCC->PLLCFGR |= RCC_PLLCFGR_PLLREN; /***************************************** * 3. 分配各时钟频率 ******************************************/ RCC->CFGR = 0; // AHB -HCLK = SYSCLK / 1 = 73.728MHz RCC->CFGR |= RCC_CFGR_HPRE_DIV1; // APB1-PCLK1 = HCLK / 4 = 18.432MHz RCC->CFGR |= RCC_CFGR_PPRE1_DIV4; // APB2-PCLK2 = HCLK / 4 = 18.432MHz RCC->CFGR |= RCC_CFGR_PPRE2_DIV4; // 选择 PLLCLK(73.728MHz) 作为SYSCLK RCC->CFGR |= RCC_CFGR_SW_PLL; // 等待SYSCLK = PLLCLK选择成功 for(;;) { if ((RCC->CFGR & RCC_CFGR_SWS) == RCC_CFGR_SWS_PLL) break; }}